Heavy deburring and rounding machine with six oscillating transversal Disc aggregates in working width 1500mm || - 2 disc aggregates infeed side with each: large diameter 250mm for a lot of grinding time, 2.2kW drive, separate Height adjustment for fine adjustment with Teflon guides and handwheel with digital counter for quick compensation of tool wear | - 2 Central disc aggregates each with: large diameter 250mm for a lot Grinding time, 2.2kW drive, separate height adjustment for fine adjustment with Teflon guides and hand wheel with digital counter for quick compensation the tool wear | - 2 disc units outlet side with each: large Diameter 250mm for a lot of grinding time, 2.2kVV drive, separate Height adjustment for fine adjustment with Teflon guides and handwheel with digital counter for quick compensation of tool wear | - Transversal oscillation of the disc units across the feed direction for Uniform tool wear, gear motor 3 kW and bilateral Toothed belt drive with infinitely variable oscillation speed via Frequency converter, two stroke stages (full stroke and small stroke for Small parts processing) | - robust, dust-resistant linear guide for Oscillation movement | - closed machine housing for less Dust pollution in the environment | - four spring-loaded rubber hold- downrollers, move together with disc station in height, additional separate Adjustment option as well as pneumatic lifting by switch (for processing small workpieces) | - Conveyor belt feed with continuously adjustable Speed ??1-5 m / min via gear motor | - pneumatically controlled Conveyor belt centering for problem-free belt run | - constant table height (Throughput height) for use in production lines | - maximum workpiece height 100mm | - Motorized height adjustment of the workpiece thickness using the up / downbutton incl. electronic digital display | - Switch for tool change, machine public to max.workpiece thickness | - Guiding of the complete grinding unit in 4 heavyunits Round guides and screw jacks with trapezoidal thread spindles | - control panelwith lockable main switch, feed switch, rotary control for Feed speed, switch for disc drive infeed with right / left rotation as well as rotary control for disc speed, switch for central disc drive with right / Left-hand rotation as well as rotary control for disc speed, switch for discspeed, Spout with right / left rotation as well as rotary control for disc speed,switch for Oscillation (full stroke / small stroke) and controller for Oscillation speed, switch for tool change | - strip brush for Conveyor belt scraper | - Extraction connection 1 x 200mm diameter | - Emergency stop button at the machine infeed and outlet | - emergency stop when the doors are open (right and left) | - Inlet protection flap for workpieces that are too thick with emergency stop | - Operating voltage 400V, 50Hz, air connection 6-8bar with maintenance unit | - Operating instructions || Machine included with: | - Combidisc 0 250 instead ofSoftdisc 0250 | - Slag hammer Disc 0 250 mm 55 ° Shore A | - Stepless speed Disc aggregates 400 - 1600 RPM, separately adjustable for two discs each at theinlet! Center / outlet via three frequency converters | - Rotating cleaning brush for Brushing off the conveyor belt, brush diameter 120mm, width 1500mm, drive via gear motor 0.37kVV | - LED lighting machine room one LED each Light bar at the inlet and outlet, protection class IP 65 | - Magnetic trackwidth 250mm Permanent magnet for holding small parts, not switchable | - Deduster UT-T3 Dry suction || Technical data dust extractor: | Motor: 3.0kW, 50 Hz / 400 V | Max. Air volume: approx. 5,200 rn 3 / h | Operating point: approx. 3,200rns / h | Max. Negative pressure: approx. 3,100 Pa | filter area: 20 m 2 | filter: 2 filtercartridges, antistatic (use category M) | intake: Ø 200 mm, left | discharge: upwards, from fan housing | version with integrated Cyclone separator, consisting of: | - pre- separator module | - integrated Cyclone | H-Line control (BG2, 3.0 kW) | Version for stainless steel dust in accordance with W3 Consists of: | - Volume flow monitoring | - Display evaluation | Discharge: Dust collection container (approx. 50 l) | Design: stationary, with Feet | Dimensions: approx. 970 x 850 x 2,785 mm (WxDxH) || - Electric Link for dry suction The suction system starts and stops with the Deburring machine | - Suction tube kit 0200 for UT-T3 -standard- for direct Connection between machine and extraction system.
The "Easy T" is the cost-effective alternative to the conventional ones grinding and deburring machines. His head consisting of a grinding wheel and a flap brush, can be swiveled by 180°. Thus, a faster Switching between the aggregates possible. Due to the weight-bearing arm the head can be easily moved over the workpiece. The result is one even edge rounding. The pad also prevents slipping of the smallest components. Furnishing : - Deburring and rounding of laser-cut or stamped sheet metal parts - Grinding head, consisting of a grinding wheel & a flap brush, can be swiveled by 180° - Working area 800 x 1300 mm - Weighted arm for easy pivoting - non-slip table pad - Ergonomic operation of the machine with the help of push buttons "On/Off" - Grinding head with infinitely variable speed via frequency converter - Handle for ergonomic handling